Keragaan Permesinan dan Keteguhan Rekat Kayu Jati Cepat Tumbuh Terdensifikasi
The objective of this study was to analyze machining performance (characteristic and quality), as well as bonding quality of densified wood, and then compared to those of un-treated (control) wood and boron-treated wood. Characteristic and quality of machining properties were directly evaluated by qualified technician during processing, while bonding quality was evaluated through its shear strength. The results showed that densification employed was able to improve machining performance and bonding quality of the 5-year-old faster-grown teakwood. Compared to control wood and boron-treated wood, machining performances of densified teakwood are greater, while bonding quality increased by 18.79 and 26.86%, respectively. The surface became much fine and even, and has similar colour to older teakwood. Analysis hierarchy process (AHP) proves that densified teakwood is the best raw material for furniture manufacturing since its machining performances, appearance, colour, and bonding quality are better either than control wood or boron-treated wood.
Keywords: AHP, bonding quality, densification, faster-grown teakwood, machining performance
Achdiawan R, Puntodewo A. 2011. Livelihood of furniture producers in Jepara. Furniture Value Chain Project Annual Report 2011. Bogor (ID): Center for International Forestry Research.
Amin Y, Dwianto W. 2006. Pengaruh suhu dan tekanan uap air terhadap fiksasi kayu kompresi dengan menggunakan close system compression. Jurnal Ilmu dan Teknologi Kayu Tropis. 4 (2): 19–24.
AWPA A3-77. 1997. Books of standard. (Includes standards on preservatives, treatments, methods of analysis, and inspection.). Granbury: AWPA.
Bekhta PA, Niemz P, Sedliacik J. 2012. Effect of prepressiang of veneer on the glueability and properties of veneer-based products. European Journal of Wood and Wood Products. 70: 99–106. https://doi.org/10.1007/s00107-010-0486-y
Bekhta PA, Niemz P. 2003. Effect of high temperature on the change in color, dimensional stability and mechanical properties of spruce wood. Holzforschung. 57: 539–546.
Blomberg J, Persson B, Bexell U. 2006. Effects of semi-isostatic densification on anatomy and cell-shape recovery on soaking. Holzforschung. 60: 322–331. https://doi.org/10.1515/HF.2006.052
Danuwihardi N. 2015. Kerapatan dan keawetan kayu jati (Tectona grandis L.f.) unggul nusantara terdensifikasi. [Skripsi]. Bogor (ID): Institut Pertanian Bogor.
Dundar T, Ayrilmis N, Candan Z. 2008. Evaluation of surface roughness of laminated veneer lumber (LVL) made from beech veneer treated with various fire retardants and dried at different temperatures. Forest Products Journal. 58: 71–76.
Faust TD, Borders BE. 1992. Using variable glue spread rates to control bond quality and reduce glue consumption in pine plywood production. Forest Products Journal. 42: 49–56.
Hasan H, Tatong B. 2005. Pengaruh pemadatan terhadap sifat fisis dan mekanis kayu Palapi. Media Komunikasi Teknik Sipil. Volume 13. No. 1. Edisi XXXI. Palu (ID): Jurusan Teknik Sipil Fakultas Teknik Universitas Tadulako.
Hill C. 2006. Wood Modification. Chemical, thermal and other process. John Wiley & Son Ltd. The Atrum, Southern Gate, Cichester, West Sussex. England (EN).
Inoue M, Nomorito M, Tanahashi M, Rowell RM. 1993. Steam or heat fixation of compressed wood. Wood and Fiber Sci. 25 (3): 224‒235.
[JAS]. Japanese Agricultural Standard. 2003. Japanese Agricultural Standard for Plywood MAFF Notification No.234-2003.
Korkut DS, Korkut S, Bekar I, Budakçı M, Dilik T, Çakıcıer N. 2008. The effects of heat treatment on the physical properties and surface roughness of Turkish Hazel (Corylus colurna L.) wood. International Journal of Molecular Sciences 9: 1772‒1783. https://doi.org/10.3390/ijms9091772
Nestri AP. 2014. Pengaruh densifikasi terhadap sifat fisis dan sifat mekanis kayu jati (Tectona grandis L.f.) Cepat Tumbuh. [Skripsi]. Bogor (ID): Institut Pertanian Bogor.
Saaty TL. 1980. The Analytic Hierarchy Process. McGraw-Hill Book Co. New York (US). https://doi.org/10.21236/ADA214804
Smith DNR, Tamblyin. 1970. Proposed scheme for international standard ters for the resistance of timber to impregnation with preservative. Ministry of Technology. Forest Product Research Laboratory. New Zeland.
[SNI] Standar Nasional Indonesia Nomor 03-5010.1-1999. Pengawetan Kayu untuk Perumahan dan Gedung.
Sulistyono, Nugroho N, Surjokusumo S. 2003. Teknik rekayasa pemadatan kayu II: Sifat fisik dan mekanik kayu Agatis (Agathis lorantifolia Salisb.) terpadatkan dalam konstruksi bangunan kayu. Buletin Keteknikan Pertanian. 17(1): 32‒45.
Wahyudi I, T Priadi, IS Rahayu. 2014. Karakteristik dan sifat-sifat dasar kayu Jati Unggul Nusantara umur 4 dan 5 tahun asal Jawa Barat. Jurnal Ilmu Pertanian Indonesia. 19(1): 50‒56.
Yovi EY, Nurrochmat DR, Sidiq M. 2013. Domestic market of Jepara’s small scale wooden furniture industries: Its potential and barrier. Unpublished project report: Mahagony and Teak furniture: Action research to improve value change efficiency and enhance livelihood (PST/2007/119). Australian Center for International Agricultural Research. Canberra (AU).
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-NonCommercial 4.0 International License. Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use. NonCommercial — You may not use the material for commercial purposes.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).